The Board Foot at a Lumber Counter

A wide board costs more than a narrow one of the same length when the price is based on volume. That still leaves the buyer to work out how much usable wood the project will get.

Stacks of sawn timber at a lumber yard in Finland
In this story 5 sections

At a lumber counter, there are several ways to hear the word foot. One buyer may be asking for enough material to go along eight feet of wall. The supplier may be talking about a unit that measures volume. A board can be eight feet long and contain only four board feet, or contain eight board feet, depending on its width and thickness. Before deciding which piece is expensive, the two people need to agree on what is being measured.

The United States Forest Service describes the board foot as a unit used for hardwood lumber in the United States. One board foot is a volume equivalent to a piece one foot long, one foot wide and one inch thick. A merchant does not need to have a piece of that exact shape in stock. The reference combines the three dimensions in a way that lets an irregular assortment be counted. Not every timber market uses the unit. The lumber yard in the photograph is in Finland and illustrates sawn boards, rather than the use of a particular American billing convention there.

Do the multiplication once with the units showing

Take two fictional pieces, each one inch thick and eight feet long. The first is six inches wide and the second is nine. The Forest Service formula multiplies thickness and width in inches by length in feet, then divides the result by twelve. For the first piece the arithmetic is one times six times eight divided by twelve: four board feet. For the second it is one times nine times eight divided by twelve: six board feet. Both have the same length. The extra width adds two board feet.

If these pieces were each priced at an invented rate of seven dollars per board foot, the first would cost twenty eight dollars and the second forty two, before any separate charges. The dollar figures tell us nothing about current rates. The comparison shows why a supplier can give the same rate for two pieces that produce different line totals. Conversely, a piece sold by the linear foot or as a whole priced board needs its own comparison. The ruler can tell you its dimensions; the listing tells you the unit of sale.

If all three input lengths are written in inches, the arithmetic changes form. A board foot contains 144 cubic inches, so the product of three inch measurements can be divided by 144. For the first piece, eight feet becomes ninety six inches. The volume from the three inch dimensions is 576 cubic inches, which is again four board feet. Writing units beside the numbers avoids an easy mistake: using 96 for the length in the mixed-unit formula and accidentally treating it as 96 feet.

Ask which dimensions are being tallied

The formula is most helpful when the dimensions are clearly defined. A quotation could refer to rough stock, stock already surfaced, or a thickness category used by that seller. Milling can remove some of the wood whose original quantity was recorded. A board listed using an earlier or nominal thickness need not measure the same thickness in its finished state. That does not in itself establish a dispute. It is a reason to look for the stated dimension and tally basis before comparing two offers.

The useful questions are practical. Is this the amount measured before or after surfacing? How did the seller measure a board with varying width? Is there a minimum purchase or a rounding convention? If two sellers use different bases, ask for enough information to compare actual prices for material that can do the same job. A report of four board feet without a description of what was measured answers a narrower question than a purchaser may have intended.

Even a good quotation cannot promise that a board fits the project. One can be long enough for a rail but unsuitable for a wide panel. A second can offer more volume but a width that does not match the required pieces. The invoice measures material according to the agreement. A cut list describes the dimensions of the parts somebody wants to make. Put the two together before deciding which pieces to buy.

What cuts off goes somewhere in the price

Say a project needs two undamaged strips six inches wide. Under a simple model one wide board containing sufficient total volume might appear to supply both. It also needs enough width to account for the material removed by the saw and for trimming. Surface defects or misaligned ends may require other cuts. A buyer who treats every billed board foot as one board foot of finished product will usually have to revise the calculation once those boundaries are visible.

Think about a hypothetical side table. The legs need length in particular directions; the top needs a usable surface across a wider area. Several short pieces could contain as much wood as one long piece. They cannot replace that long piece if the design calls for an unjoined member of a particular length. Conversely an area unsuitable for the top could supply part of another component. The useful yield depends on where usable parts fit, not simply on the total material the boards contain.

Grading and project yield are related rather than identical. The Forest Service's grading introduction discusses the clear portions used within a grading system. A customer should pay attention to what that system measures, then to the size and position of the parts they need. An attractive characteristic for one purpose might be a limitation for another. A declaration on a supplier's tag is a useful input to the decision; it does not replace the shapes of the pieces on the cut list.

A cheaper rate can be a more expensive fit

Consider two fictional offers for a job. One offers ten board feet at six dollars each, costing sixty dollars. The other offers eight board feet at seven dollars, costing fifty six. The larger quantity is cheaper per unit. If both quantities can produce the set of parts, the second costs fewer dollars. If the smaller order lacks a necessary wide board, that arithmetic stops just short of a workable decision. A missing part can make an extra trip or order necessary. Those are costs, but they do not belong in the board foot formula.

A furniture maker doing the same work weekly might keep rough records of which purchased pieces yielded which finished parts. That gives practical evidence for selecting supply quantities. Another buyer making one unusual object might start with actual minimum widths and lengths at the counter. In both cases use a simple comparison of resources needed, tolerable variation and total price. Paying a lower rate on raw volume is useful only to the extent the raw volume can be made to answer the job.

Stacked boards can also be sold in bundles rather than individually. A total tally tells a buyer about the bundle, but may not cover the distribution of required widths if those are important. Asking for the piece list, an indication of the range or permission to select pieces can explain why two bundles with the same tally have different value for one project. This is the same issue on a larger shelf. Replacing a pile of casual impressions with one volume number helps, until it removes a dimension of the buyer's question.

Keep both calculations in view

A stock record can preserve one useful fact and omit another. Imagine a shop with a purchased bundle containing enough billed volume to finish several small tables. After two tables are made, pieces left from short cuts may still have measurable volume. Recording the remaining quantity is sensible for inventory, but the next job might need several longer parts the offcuts cannot provide. A note of the sizes still in the rack, rather than volume by itself, lets the shop use the material it already has where it fits.

Purchases made on successive days can make that difference harder to keep straight. Two batches may have the same thickness and a similar colour, yet contain suitable widths in different proportions. Keeping the relevant purchase record with the cut list lets a later buyer trace what made one batch easier to use. That kind of evidence is more helpful for planning an order than a general memory that the higher priced bundle had nicer boards.

A useful note starts with material as quoted: unit, rate and the dimensions or tally that set it. Give intended finished parts their own line. If there is a gap between purchased and useful volume, say whether it comes from width, machining, shape or some other restriction. This sounds like more work than reading a price tag. It usually saves comparing things the tag was never meant to make equivalent.

Keep a delivery charge or a separately quoted milling service visible as well. A low material rate and a higher total delivered price can coexist. Being able to point to the line that changed is more useful than simply calling the supplier expensive.

The word foot is doing honest work in both conversations at the counter. The first use helps a person describe how long the material must run. The second helps a supplier estimate the volume being sold. The labour of making something belongs between the two. It is what makes a bundle of wood become longer, shorter, wider or narrower pieces that can actually be used.

Further reading